# Shading Solar Panels – Series or Parallel?

Like it or not,

Shade is the enemy of solar panels.

If you have an off-grid homestead, RV, van, or even a sailboat you could significantly reduce the power output of your panels.

In this article, I’m going to explain how you can remedy shading on your solar panels.

When there is shade on solar panels it will reduce the current of that panel.

Let’s say you have a panel that has a rating of 17.5 Volts and 5.8 Amps, it will produce 100Watts.

Now if shade comes over the panel, the current could drop to 3 Amps, but the voltage stays the same, resulting in 52.5 Watts (3 Amps x 17.5 Volts).

There is really nothing you can do about this if you have a single solar panel.

Shade has an effect on current, while temperature has an effect on voltage.

## What is the effect of shaded PV cells in series and parallel?

The problem arises if you have multiple solar panels.

Multiple solar panels can be connected in series or parallel.

Most of the time, your panels will be connected in series. Want to know why? Check out my article on series and parallel wiring of solar panels.

Solar panels should always be wired in series if there is no shading problem and the total voltage stays under the charge controller max input voltage.

### Effect of shading in series connections

If you expect to have shade on your panels, adding panels in series is not the best configuration.

Remember that in series the voltage is added up and the current stays the same?

If there is shade on one panel, the current will drop. In a series connection, the current will take the lowest value in the string which is 3 amps in the following example:

The shaded spot on one panel will decrease the string of panels to 3 amps at 52.5 volts. This means that the total power will be reduced from 300 Watts (52.5 Volts x 5.8 Amps) to 157 Watts (52.5 Volts x 3 Amps).

Are you keeping up?

Let’s look at what parallel does.

### Effect of shading in parallel connections

If we do the same experiment with parallel connections, we see that we have a higher power output.

This is because in parallel connections voltage stays the same but current is added together.

Remember that solar irradiance (sunshine) only has an impact on the current and not on voltage?

Therefore we add 3 amps + 5.8 amps + 5.8 amps to become 14.6 amps total. If we multiply this by the voltage of 17.5 we become 255 Watts which is higher than the 157 Watts in a series connection.

If you expect shading on your solar panels, I recommend putting them in a parallel configuration.

If you wire your panels in parallel, the current is higher which means you need to increase the wire diameter. This will increase the cost of your solar system. Therefore, you need to include a combiner box and make the distance between the combiner box and the charge controller as short as possible.

#### Conclusion

If you have no problems with shade, you can wire your panels in series. Wiring panels in series in cheaper and is better for your MPPT charge controller. Most MPPT charge controllers can take a maximum of 100 Volts. If you exceed this, you need a hybrid solar panel setup (series and parallel combination).

If you have an RV or a van and plan to move a lot, you are better off with a parallel connection. This is because you are not always certain if there is going to be sunshine all the time on all your panels. Yes, it will cost you more in wiring but it will pay off in the long term. Especially if your battery bank is running low.

## FAQ

### Series or parallel solar panels for RV?

In an RV, you will expect shading to happen. It can be a branch or a fallen leaf on the panels. In an RV you want to harvest every watt you can. That’s why you should wire the panels of your RV in parallel. It will cost you more in wiring, but it is worth it.

### Is it better to series or parallel solar panels?

You should wire your panels in series if there is no shade. If there is shade, the best way to wire your panels is in parallel. Don’t forget that the wires need to be bigger when wiring in parallel. This will increase the cost. Keep in mind that you can only add so many in panels in series up until the charge controller allows it.

### How does shading affect solar panels in parallel?

Shading affects the current (A) of the solar panel. The voltage (V) is affected by temperature.

### Do solar panels charge faster in series or parallel?

This is a tricky question. Generally, batteries get charged quicker in series because of low light in the early morning and late evening. Because voltage is added up in a series connection, the minimum required voltage to start charging the battery is reached quicker.

### What type of solar panel works best in shade?

Improvements in solar panel technology make polycrystalline and monocrystalline practically the same. There is no significant difference in how both technologies handle shaded conditions. However, polycrystalline technology has a bigger surface area than monocrystalline for the same amount of power generation.

### What happens if a solar panel is partially shaded?

The current of the solar panel that is shaded will drop significantly, reducing the total current output of the whole series string.

### Do solar panels work in the shade?

You will get a tiny amount of power from shaded solar panels compared to the full sun. Let’s say it’s about 10-20% of the rated power.

Get Started With Off-Grid Solar Power

I have written a book that contains all the information you need to get started with off-grid solar power.

With over 1,300 reviews at 4.5 stars, I can almost guarantee you that this book will save you \$100’s on buying the right equipment.

You can buy it here on Amazon.com

### 17 thoughts on “Shading Solar Panels – Series or Parallel?”

1. Can you add what happens if the shading of a cell of one panel is so severe that a bypass diode “kicks in” causing the loss of say 1/3 of the panel.

• Once the resistance of the cells is high enough, and it’s more than the resistance of the diode, the current will go through the diode. Preventing hotspots for forming on the panel. I don’t know the actual value or time when the diode takes over.

• The diagrams above “Effects of shading on a solar system in parallel. The image is taken from my book.” do not initially make sense because the “100W” panels are actually making a little more than 100W.
eg the paralleled panels
52W+100W+100W = 252W
while it is shown as 255.5W

• I rounded up the power of each panel to make it look simpler. So each 100W panel is ‘missing’ 1,5 Watts. I’m sure you understand.

2. AE Solar makes a panel with a diode on each cell so that shaded cells are bypassed. Shouldn’t that make the loss from shade the same for series as it is for parallel connections of two panels?

• From my understanding, that would solve the problem we face with series connections partially. But that will come at a price. It’s certainly promising, but most people always put their panels in the sun. I can see it being useful for RV’s or boats.

The reason I say partially is that the current would still be reduced but in a smaller amount. If you then connect them in series, the panels will drop down to the current of the lowest value panel like shown in the series example. If you expect shade I still recommend using parallel wiring.

• My understanding is that when cells are bypassed, it is only volts that are lost. If all the other cells are unimpaired then you wouldn’t lose any current. So, in my example you could lose 1/3 of the voltage of one panel and then you would be better off with the two panels being connected in series. The application I’m interested in is a narrowboat where the panels regularly experience unequal light levels. I’ve heard of people wiring their two panels both ways with a switch so that they can select whichever scheme (serial or parallel) gives the greater output in the prevailing conditions.

3. if i have 4 panels @ 270w and only 1 gets shading, should i have 3 in series and parallel up the on that gets shaded

• The first option is to wire them all in parallel. The second option is to wire the three sunny panels in series to one charge controller and the shaded panel to another charge controller.

• Hi
On this situation don’t need to wire them in parallel and series but only in series. What you need to introduce is a bypass diodes on each panel so that if 1 panel is shaded the bypass will take over and current on whole string in series will not be affected with shaded panel.

• In my opinion, that’s not the ideal solution.

4. Thank you

Somehow in my mind I had applied the serial panel case to single panels, thinking that even partial shade would severely impact output. Today I was working on a simple gate opening system and noted the shaded panel still provided 20V but only 500mA (reduced but not useless), which surprised me and lead to further education ðŸ™‚

• Depending on how the shade casts on the panel, the output will be severely reduced. If it’s a tree trunk over the width of the panel, then the output would be reduced a lot. If it’s a small leaf, the bypass diodes will work and the panel would still give 2/3 of its rated output. Indeed, the solar radiation will have an effect on the current while the temperature has an effect on the voltage. So what you saw there is perfectly normal.

5. I would be interested in understanding what happens if a solar panel is (partially) broken due to several reasons, e.g. aging or a manufacturing problem.
My understanding is that this would also have an effect if connected in series, right!?
Following this thought isnâ€˜t it not worth spending a little bit more on wiring and to always consider a parallel configuration?
What are the real technical disadvantages of a parallel configuration besides the financial?
Thank you!